How to add and reset Centralite products on Hubitat Elevation hub

Authored by: Support.com Tech Pro Team

1. Introduction

How to add and reset Centralite products on Hubitat Elevation hub

 

 

2. Resolution

Pearl Thermostat  

Product Number

Device Type

Protocol

3000-G

Thermostat

Zigbee

Factory Reset

  1. Enter Programming Mode, navigate to Menu ID “17”, press HOLD, then navigate to option “11”, then press HOLD again.
  2. The device will then factory reset itself and begin looking for an open network to join.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Enter Programming Mode, navigate to Menu ID “17”, press HOLD, then navigate to option “11”, then press HOLD again.
  3. The device will then factory reset itself and begin looking for an open network to join.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.

3-Series Smart Outlet  

 

Product Number

Device Type

Protocol

3200-G

Outlet

Zigbee

Factory Reset

  1. Unplug any devices from the module and unplug them from the wall.
  2. Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Unplug any devices from the module and unplug them from the wall.
  3. Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.

3-Series Door & Window Sensor  

 

Brand

Device

Product Number

Device Type

Protocol

Centralite

3-Series Door & Window Sensor

3300-G

Contact Sensor

Zigbee

Factory Reset

  1. Slide the sensor of the mount, remove the cover, and remove the battery.
  2. While holding down the reset button, reinsert the battery to factory reset the device.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Slide the sensor off the mount and remove the cover. Remove the battery for 10 seconds and replace

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.
  2. Slide the sensor of the mount, remove the cover, and remove the battery.
  3. While holding down the reset button, reinsert the battery to factory reset the device.

3-Series Motion Sensor  

 

Product Number

Device Type

Protocol

3305-G

Motion Sensor

Zigbee

Factory Reset

  1. Slide the sensor of the mount, remove the cover, and remove the battery.
  2. While holding down the reset button, reinsert the battery to factory reset the device.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Slide the sensor off the mount and remove the cover. Remove the battery for 10 seconds and replace

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.
  2. Slide the sensor of the mount, remove the cover, and remove the battery.
  3. While holding down the reset button, reinsert the battery to factory reset the device.

3-Series Micro Door Sensor  

 

Brand

Device

Product Number

Device Type

Protocol

Centralite

3-Series Micro Door Sensor

3323-G

Contact Sensor

Zigbee

Factory Reset

  1. Slide the sensor of the mount, remove the cover, and remove the battery.
  2. While holding down the reset button, reinsert the battery to factory reset the device.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Slide the sensor off the mount and remove the cover. Remove the battery for 10 seconds and replace

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.
  2. Slide the sensor of the mount, remove the cover, and remove the battery.
  3. While holding down the reset button, reinsert the battery to factory reset the device.

3-Series Micro Motion Sensor  

 

Brand

Device

Product Number

Device Type

Protocol

Centralite

3-Series Micro Motion Sensor

3328-G

Motion Sensor

Zigbee

Factory Reset

  1. Slide the sensor of the mount, remove the cover, and remove the battery.
  2. While holding down the reset button, reinsert the battery to factory reset the device.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Slide the sensor off the mount and remove the cover. Remove the battery for 10 seconds and replace

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.
  2. Slide the sensor of the mount, remove the cover, and remove the battery.
  3. While holding down the reset button, reinsert the battery to factory reset the device.

4-Series Smart Outlet  

 

Brand

Device

Product Number

Device Type

Protocol

Centralite

4-Series Smart Outlet

4200-C

Outlet

Zigbee

Factory Reset

  1. Unplug any devices from the module and unplug them from the wall.
  2. Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Unplug any devices from the module and unplug them from the wall.
  3. Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.
  4. After the Smart Outlet has successfully joined a ZigBee network, the status LED will turn solid green

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.
  2. Unplug any devices from the module and unplug them from the wall.
  3. Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.