How to add and reset Hank products on Hubitat Elevation hub

Authored by: Support.com Tech Pro Team

1. Introduction

How to add and reset Hank products on Hubitat Elevation hub

 

2. Resolution

Factory Reset

  1. Press and holding the center "Z-button" for 20 seconds.
  2. Release the button after 20 seconds and the LED will stay yellow for 3 seconds.
  3. Within the 3 second period where the LED is yellow, short-press the Z-button to reset the controller to factory defaults.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Insert the battery.
  3. Triple click the center "Z-button".
  4. If inclusion is successful, the LED will flash blue for less than 5 seconds, and then it will remain solid for 15 seconds.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. If exclusion is successful, the LED will flash orange for less than 5 seconds, and then it will remain solid for 3 seconds.

Device

Product Number

Device Type

Protocol

One-Key Scene Controller

HKZW-SCN01

Button Controller

Z-Wave Plus

Device

Product Number

Device Type

Protocol

Four-Key Scene Controller

HKZW-SCN04

Button Controller

Z-Wave Plus

Factory Reset

  1. Press and holding the center "Z-button" for 20 seconds.
  2. Release the button after 20 seconds and the LED will stay yellow for 3 seconds.
  3. Within the 3 second period where the LED is yellow, short-press the Z-button to reset the controller to factory defaults.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Insert the battery.
  3. Triple click the center "Z-button".
  4. If inclusion is successful, the LED will flash blue for less than 5 seconds, and then it will remain solid for 15 seconds.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. If exclusion is successful, the LED will flash orange for less than 5 seconds, and then it will remain solid for 3 seconds.

Device

Product Number

Device Type

Protocol

RGBW LED Bulb

HKZW-RGB01

Bulb

Z-Wave Plus

Factory Reset

  1. Factory reset is achieved by performing a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Toggle power to the bulb off and on 3 times quickly.
  4. Within 3 times toggling the bulb, the final ending state of the switch or plug must be on.
  5. If the exclusion is successful, the RGB BULB will quicly flash orange for less than 5 seconds, and then it will remain solid for 3 seconds.
  6. The bulb will remain warm white after the exclusion procedure is complete.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Make sure power to the bulb is disconnected and the RGB BULB is close to the hub.
  3. Insert the bulb into a socket and then turn it on.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Toggle power to the bulb off and on 3 times quickly.
  4. Within 3 times toggling the bulb, the final ending state of the switch or plug must be on.
  5. If the exclusion is successful, the RGB BULB will quickly flash orange for less than 5 seconds, and then it will remain solid for 3 seconds.
  6. The bulb will remain warm white after the exclusion procedure is complete.