How to add and reset Heatit products on Hubitat Elevation hub

Authored by: Support.com Tech Pro Team

1. Introduction

How to add and reset Heatit products on Hubitat Elevation hub

 

2. Resolution

Thermostat 

Device

Product Number

Device Type

Protocol

Z-Temp2

45 126 66

Thermostat

Z-Wave Plus

Factory Reset

  1. Press and hold the link button for 20 seconds
  2. rES will be displayed.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the link button 3 times quickly.
  3. The thermostat will display INC when the thermostat is successfully included.
  4. If inclusion fails, Err (error) will appear.
  5. Successful inclusion will be confirmed by Hubitat Elevationâ„¢
  6. Watch the status in the device details page to confirm proper operation.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the link button 3 times quickly and wait for the exclusion process to finish. This will take a few moments to complete.

Device

Product Number

Device Type

Protocol

Z-TRM3

54 305 98

Thermostat

Z-Wave Plus

Factory Reset

  1. Press both the Right and Center (down and confirm) buttons for 20 seconds.
  2. The thermostat will be factory reset.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press and hold the center button until OFF is shown on the display (approx. 10 seconds).
  3. Press the down button 5 times until you reach CON
  4. Press and hold until the display shows a rotating light pattern. The thermostat will display INC when the thermostat has successfully joined the Z-Wave network.
  5. If inclusion fails, Err (error) will appear.
  6. Successful inclusion will be confirmed by Hubitat Elevationâ„¢
  7. Watch the status in the device details page to confirm proper operation.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the down button 5 times until you reach CON
  4. Press the center (confirm) for approximately 2 seconds and wait for the exclusion process to finish. This will take a few moments to complete.

Dimmer 

Device

Product Number

Device Type

Protocol

Z-Dim

14 444 44

Dimmer

Z-Wave Plus

Factory Reset

  1. By pressing and holding the main button for 20 seconds, the dimmer will be factory reset.
  2. The connected light source will blink once and go in the OFF state if successfully reset.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the main button on the dimmer 6 times quickly.
  3. Successful inclusion will be confirmed by Hubitat Elevationâ„¢
  4. Watch the status in the device details page to confirm proper operation.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the main button on the dimmer 6 times quickly. and wait for the exclusion process to finish. This will take a few moments to complete.

Repeater 

Device

Product Number

Device Type

Protocol

Z-Repeater

45 126 86

Repeater

Z-Wave Plus

Factory Reset

  1. When the device is excluded from the Z-Wave network, it will revert to factory settings.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Plug-in the device and within 1.5 seconds, press the function button 3 times.
  3. Successful inclusion will be confirmed by Hubitat Elevationâ„¢

Exclusion from the Z-Wave Network

  1. Unplug the device.
  2. From the device's details page, select Remove Device, then Remove
  3. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  4. Plug-in the device and within 1.5 seconds, press the function button 3 times.
  5. Wait for the exclusion process to finish. This will take a few moments to complete.

Smoke Detector 

Device

Product Number

Device Type

Protocol

Z-Smoke 230V

45 126 89

Smoke Detector

Z-Wave Plus

Factory Reset

  1. Excluding the device from the Z-Wave network will reset it to factory settings.

Join the Z-Wave Network

  1. When power is applied, the smoke detector initiates a 1 minute warm-up period and will automatically enter inclusion mode.
  2. After the calibration process is finished, access inclusion mode by pressing the function button 3 times within 1.5 seconds. 
  3. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  4. Successful inclusion will be confirmed by Hubitat Elevationâ„¢
  5. Watch the status in the device details page to confirm proper operation.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the function button 3 times within 1.5 seconds and wait for the exclusion process to finish. This will take a few moments to complete.