How to add and reset Schlage products on Hubitat Elevation hub

Authored by: Support.com Tech Pro Team

1. Introduction

How to add and reset Schlage products on Hubitat Elevation hub

 

2. Resolution

Factory Reset

  1. Disconnect the 9V battery.
  2. On the lock keypad, press and release the Schlage button.
  3. Reconnect the battery and wait until the Schlage button is no longer lit.
  4. Within 10 seconds, press and hold the Schlage button until it lights Green and the lock beeps.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Enter the 6 digit programming code.
  3. Wait for the Schlage button will flash Amber 3 times. It will be accompanied by 3 beeps.
  4. Press the Schlage button and the 0 key.
  5. If successful, the Schlage button will be flashing Amber.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Enter the 6 digit programming code.
  4. Wait for the Schlage button will flash Amber 3 times. It will be accompanied by 3 beeps.
  5. Press the Schlage button and the 0 key.
  6. If successful, the Schlage button will be flashing Amber.

Device

Product Number

Device Type

Protocol

LiNK Deadbolt

BE-369

Lock

Z-Wave

Device

Product Number

Device Type

Protocol

LiNK Deadbolt

FE-599

Lock

Z-Wave

Factory Reset

  1. Disconnect the 9V battery.
  2. On the lock keypad, press and release the Schlage button.
  3. Reconnect the battery and wait until the Schlage button is no longer lit.
  4. Within 10 seconds, press and hold the Schlage button until it lights Green and the lock beeps.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Enter the 6 digit programming code.
  3. Wait for the Schlage button will flash Amber 3 times. It will be accompanied by 3 beeps.
  4. Press the Schlage button and the 0 key.
  5. If successful, the Schlage button will be flashing Amber.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Enter the 6 digit programming code.
  4. Wait for the Schlage button will flash Amber 3 times. It will be accompanied by 3 beeps.
  5. Press the Schlage button and the 0 key.
  6. If successful, the Schlage button will be flashing Amber.

Device

Product Number

Device Type

Protocol

Connect Deadbolt

BE-468 / BE-469

Lock

Z-Wave

Factory Reset

  1. Disconnect the batteries
  2. Press and hold the outside Schlage button
  3. While holding the outside Schlage button, then reconnect the batteries.
  4. Release the Outside Schlage Button. NOTE: If you are moving the lock to a new door, install the lock on that door before continuing.
  5. To check that the lock was reset, press the outside Schlage button and enter one of the Default User Codes.
  6. If the reset was successful, the lock will perform a setup routine. Wait until the bolt stops moving. The reset and setup are complete.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the Schlage button.
  3. Enter the 6 digit programming code.
  4. Press 0
  5. √ indicates the lock successfully joined the Z-Wave network, while an X indicates that it did not successfully join the network.

Verify Z-Wave connection status from the lock

  1. Remove the battery cover.
  2. Disconnect the battery connector.
  3. While watching the inside Schlage button, reconnect the battery connector.
  4. The inside Schlage button will flash if the lock is enrolled.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Schlage button.
  4. Enter the 6 digit programming code.
  5. Press 0
  6. √ indicates the lock was successfully excluded the Z-Wave network, while an X indicates that it did not successfully leave the network.